Fanuc 21i-t parameter manual

Upload aoaby.

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.

Fanuc 21i-t parameter manual

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Error pulse between two spindles when synchronizing phases in the serial T, M spindle synchronization control mode.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems.

Fairuza balk nude

N3 Fbbbb ; - Fbbbb is assumed to be specified in the G98 mode. QSR Before a multiple repetitive canned cycle G70 to G73 is started, a checkto see if the program contains a block that has the sequence numberspecified in address Q is:0 : Not made. NOTE When command multiplier is 1 to 48, the set value must be determined so that an integer can be set for command multiplier. Fanuc 16i 18i i i Parameter Manual. This document is based on information available at the time of its publication. Each bit has a different meaning. Servo loop gain multiplier of the spindle for gear 2 T For an axis under diameter programming, set it by a diameter value. Generally, set the positioning deviation for rapid traverse plus somemargin in this parameter. CMV When a move command and auxiliary function are specified from theCNC, and the system is awaiting the auxiliary function completion signalafter completion of the specified axis movement:. Block B G01 Angle subtended by two straight lines Angle subtended by an arc and its tangent. Search Advanced search…. When the spindle synchronization option is provided, it isset automatically when power is switched on. When P is not specified, the data for all tool groups is cleared before the tool life management data is registered.

.

If a value other than 0 is specified, proper straight lines and arcs cannot be obtained. In polar coordinate interpolation mode, the feedrate component on arotation axis increases as the tool moves closer to the center of aworkpiece. NOTE A program number can also be set on the setting screen. When the fan motor error is detected, an overheating alarm occurs. When this option is used, however, manualreference position return always results in a workpiececoordinate system being established based on theworkpiece origin offsets parameters No. Axis linear axis specification for polar coordinate interpolation Axis rotary axis specification for polar coordinate interpolation [Data type] Byte [Valid data range] 1, 2, 3, With the extended specification, an arbitrary number of such M codes from 1 to can be selected by parameter setting See parameter No. EXK The input character extension function is: 0 : Not used. When the reference position setting with mechanical stopper is used, thisparameter sets the feedrate used for withdrawal along an axis after themechanical stopper has been hit. This parameter sets the limit value of a spindle positioning deviationduring movement in rigidtapping.