Lawn mower starter cord replacement

With perfect weather, you plan to go out to give your lawn a nice trim. You use a push mower that has never let you down in all these years. Lawn mower starter cord replacement other end is spinning back into the starter assembly. You are not the only one with this problem.

Own a lawnmower long enough, and eventually, you will experience small engine pull cord failure. Whether your lawnmower pull cord has seen its fair share of uses or it fails before its time due to quality, these seven simple steps will show you exactly how to replace pull cord on mowers to get you back up and running before your next mowing mission. SGT KNOTS Dacron Polyester Pull Cord is the heavy-duty, ultra-reliable replacement pull cord and starter rope every landscaping business, homeowner, or neighborhood lawn care kid should have hanging in their garage for on-the-fly fixes. This cord is as cost-effective as it is reliable with a Dacron polyester solid-braid construction resistant against abrasion and wear. Snag this cord in either 4, 5, or 6 diameters and lengths of 10ft and 25ft, or spools of 50ft, ft, and 1,ft for a never-ending supply of replacement pull cord perfect for everything from mowers, generators, leaf and snow blowers, and more. Now that you know how to replace a mower pull cord, you can move onto your next DIY repair or improvement project.

Lawn mower starter cord replacement

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope. While nylon rope is a sturdy material, the friction between the rope and the starter housing will eventually wear it down. So, no matter how careful you are with your pull starter, the time will come when your cord will wear down and need replacing. After all, the cord is designed to be a certain length to turn over the engine and get the fuel pump pumping and the coil sparking the spark plug. You should be able to find this information in your user manual. Before I tackle any repair with my lawn mower, I always pop off the spark plug to avoid any unexpected accidents. So, pull off the spark plug cable and tuck it out of the way. The first job is to remove the starter assembly from your lawn mower. My starter assembly is attached to the lawn mower with four bolts that can be removed with either a flathead screwdriver or a nut driver. So, inspect your mower and see what tool you need to use, then remove the mounting bolts and lift the starter assembly off your lawn mower. Next, pull the starter cord all the way out of the starter assembly so that there is no more cord around the pulley. If this is a bit too tricky, just grab some assistance. Use your needle nose pliers to pull the knot from within the pulley. Next, cut the knot off inside the pulley with scissors and pull the cord from the starter assembly.

I've always had a keen interest in lawn care as long as I can remember. Connect the cord to the pull handle: 1. Jeremy Ramos says:.

By: Author John Cunningham. Replacing a pull cord can be challenging, especially if the recoil spring gets loose. Taming a recoil spring can be like herding cats. Replacing the cord requires the removal of the pull start assembly. Some manufacturers, like Honda, make it easy. Other mowers may take a little more work. If your spring is damaged or unravels, go ahead and buy a whole spring and pulley.

Written by: Steve. October 3, As an Amazon Associate we earn from qualifying purchases more. If you own a pull start lawn mower you will eventually find yourself holding the severed handle of a broken starter cord. Here in Florida, two thirds of the year is one continuous lawn mowing session. That translates to lots of cord tugs. Thankfully, starter cord replacement is simple wear and tear maintenance that you can easily do yourself.

Lawn mower starter cord replacement

Are you struggling with a broken pull cord on your lawnmower? With our step-by-step instructions, your Briggs and Stratton lawnmower will be up and running quickly. How to replace the pull cord on a Briggs and Stratton lawnmower:.

Small snowcat for sale

September 30, at pm. December 16, at am. July 31, at am. The other end is spinning back into the starter assembly. Remove the paper towel from the dipstick opening, slide the dipstick tube into the engine and secure it with the screw. Blockage — Grass and stuff stopping the blade from turning, the simple fix here. Other mowers may take a little more work. Remove the screw that secures the dipstick tube to the housing. June 5, at pm. Then, allow the tension on the pulley to pull in the remainder of the cord until the start handle meets the starter housing. Main causes: damaged cutting blade, loose cutting blade, damaged flywheel key, engine needs tune up…. The starter housing on my starter assembly has a small recess that the knot sits in.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem. And fortunately, it is easy to get done DIY.

February 7, at pm. Now, take the hanging rope and tie a big loose knot in the middle. Salvador Holmes says:. If your pull cord is hard to pull stiff , make sure the bail lever is held during the starting process. Allan Weaver says:. Replace the old pull string with the new one 1. Sylvia Bates says:. Working with recoil springs can be dangerous; removing the pully from the assembly comes with the risk of the spring breaking free. Use your needle nose pliers to pull the knot from within the pulley. Remove the engine blower housing. Instead, allow the pulley to slide through your fingers until the knot you just tied hits the starter assembly.